







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Enterprise, NV: What It Costs and How Fast It Goes Up
A chain link fence in Enterprise, NV typically runs $3,500 to $9,000 for a standard residential lot, and most jobs are built in one to three days once the permit and utility locates clear. The range covers materials, posts, concrete footings, and cleanup. The low end is a short 4-foot run on flat ground; the high end is a tall, long perimeter with rock excavation through caliche. Call (888) 282-1693 for a free on-site estimate and a written line-item quote before anything gets ordered.
How We Build a Chain Link Fence Here, Start to Finish

Chain link is a fast product, but the sequence matters. Most of the durability lives in what happens before the mesh ever goes up. Here’s how a job actually runs.
Stage 1: Walk the line and mark utilities (day 1)
We walk the property line with you, confirm corners and gate locations, and call in the 811 utility locate. In Enterprise that locate is non-negotiable: irrigation lines, gas, and the low-voltage runs the original builder put in are often shallower and closer to the fence line than you’d guess. You decide the fence height, gate swing direction, and whether the line follows the property line or sits a foot inside it.
Stage 2: Layout and excavation (day 1 into day 2)
We string the line, set post spacing at 8 to 10 feet, and start digging. On south-valley lots this is where the schedule can flex. Caliche hardpan sits under a lot of Enterprise subdivisions, and a plain auger won’t cut it. We bring rock-breaking equipment so we aren’t hand-digging 30 post holes in 105-degree heat. That step alone can add a half day on a badly caliche-bound lot.
Stage 3: Set posts and pour concrete (day 2)
Posts go in, get plumbed, and get set in concrete footings sized to the fence height and wind exposure. Terminal posts at corners, ends, and gates get larger footings and thicker wall. In the summer we pour at dawn to beat the heat, because concrete cured in the afternoon sun of a Mojave July can flash-set and lose strength. You’ll see the posts sitting overnight while the concrete cures.
Stage 4: Rails, tension wire, mesh, and gates (day 3)
Top rail, tension wire or tension bars depending on the spec, then the fabric gets stretched and tied off. Gates hang last so the posts have cured. This is the day the fence actually looks like a fence. Stretch tension is where cheap installs fail, so we tension properly at every terminal rather than drape the mesh and call it done.
Stage 5: Walk-through and cleanup (end of day 3)
We walk the line with you, check gate swing and latch, clear spoils, and hand over the written workmanship warranty. If anything needs a tension adjustment, it happens before we leave the property. This is also when you’ll want to think about whether the fence ties into other exterior work later – homeowners often pair this with Door Installation in Enterprise if a gate and a side entry are being planned together.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Chain Link Options You’ll Actually Choose Between
- Height: 4, 5, or 6 feet. Four feet is common for marking a side yard or containing a dog; six feet is the standard for real privacy and pool-area code compliance. Height drives post spacing and footing size, so it’s the first cost lever.
- Gauge of mesh and wire. A lighter 11.5-gauge fabric is the budget choice and lasts fine in low-traffic yards. Heavier 9-gauge lasts longer against dogs, wind flex, and kids climbing it, and it holds its shape better over the years.
- Galvanized vs. vinyl-coated. Plain galvanized is the cheapest and holds up in dry desert air. Vinyl-coated (usually black or green) looks finished, blends against desert landscaping, and adds a few dollars per linear foot.
- Post spec. Thin-wall posts are the reason cheap fences lean after a few summers. We spec heavier wall on corners and gates where wind and swing load concentrate.
- Gates and hardware. Walk gates, double drive gates, self-closing hinges for pool compliance. Cheap latches are the first thing to fail, so we use hardware rated for daily use.
What a Chain Link Fence Costs in Enterprise, NV

Most residential chain link jobs here land between $3,500 and $9,000. A short 4-foot run on a flat lot sits at the low end; a 6-foot, 200-foot perimeter with double gates and rock-breaking sits at the top. Here’s where the variables push the number:
| Line item | Typical range |
|---|---|
| Short run (50-80 ft), 4 ft height | $3,500 – $4,500 |
| Mid run (100-150 ft), 5-6 ft height | $4,500 – $6,500 |
| Long perimeter (200+ ft), 6 ft + gates | $6,500 – $9,000 |
| Caliche rock-breaking surcharge | $400 – $1,200 |
| Gate (walk or drive) per unit | $250 – $900 |
What pushes a job to the high end: linear footage, height, mesh gauge, gate count and type, and how much rock we hit at excavation. What’s included in a written estimate: materials, posts, concrete, tension hardware, gate hardware, excavation, cleanup, and permit pulling. What’s typically excluded: removing an existing fence (a separate line), landscaping repair after the line is cut, and anything electrical or plumbing that runs through the fence line.
See the difference
Before
After
Before
After
Before
AfterWhat Enterprise Homes Specifically Do to This Job
Enterprise was built out fast and mostly by a handful of big production builders, so a fence contractor working here runs into the same assembly block after block: wood-frame construction, stucco walls, slab-on-grade foundations, and rear property lines that follow the original tract plat. That matters because the property line on a 2000s-era subdivision plat is often tighter to the neighbor’s structure than homeowners expect. We stake the line carefully, especially around the townhome clusters and the denser mid-rise pockets along the resort corridor edges, so the fence doesn’t cross a line you don’t own.
Then there’s the ground. Caliche hardpan under a lot of south-valley Enterprise lots turns what looks like a two-hour dig into a rock-breaking job, and we plan for it up front rather than surprise you mid-build. The desert climate adds its own demands: UV exposure that eats cheap plastic gate hardware, and monsoon-season runoff that will pool on the downhill side of a fence if grading isn’t handled. We grade so water doesn’t pocket against posts. And this is HOA-governed territory: most of the newer subdivisions have design review that dictates fence height, color (usually the vinyl-coated black or green), and whether the finished side must face the neighbor. That design review happens before permits, so check it early. We pull the permit and handle the inspection chain, but HOA approval sits with you.
Serving Enterprise, NV – Our Local Coverage Area
We serve Enterprise and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Chain Link Fence in Enterprise

Most standard residential jobs take one to three days of on-site work once the permit clears. A short 4-foot run can be done in a day; a long 6-foot perimeter with gates takes three. Permit turnaround and utility locate scheduling add a few days before we ever show up, so plan on roughly a week from estimate to installed fence in typical conditions.
Yes, most residential fences in Enterprise require a permit, and the review covers height and placement relative to the property line. We pull the permit and handle the inspection. If your subdivision has an HOA design review, that runs separately and usually needs to clear first. Call (888) 282-1693 and we’ll walk you through what applies to your lot.
Yes, in most cases. We call in the 811 utility locate before any digging, mark the plumbing, irrigation, and low-voltage lines, and route post holes around them. Where a post has to move a foot or two to clear a line, we adjust spacing. Full demolition of an existing fence is a separate scope if you need it gone.
Expect $3,500 to $9,000 for a typical residential chain link fence, depending on length, height, gauge, gates, and how much caliche we hit. A written line-item quote is free, and the number doesn’t change once work starts. Call (888) 282-1693 for an exact quote.
Every chain link fence we install is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship: post setting, tension, gate hang, and footing. Material defects are covered by the manufacturer’s warranty on the mesh and hardware.
Get a Free Chain Link Fence Estimate in Enterprise
Call (888) 282-1693 and a live person answers, any hour. We’ll set a time to walk your line, check the ground and the plat, and hand you a written line-item quote. If you’re planning fence work as part of a bigger exterior project, a good next stop is Fence Installation in Enterprise for the wider scope, or the main Fence Installation page for how we run the full job.
Written by the team at Groundwork Construction Co.












